It is very easy to change the locks on your home by yourself. To have a new lock, all you need to do is remove the cylinder and change the pins. All you need is a house rekey kit at the hardware store. It is not uncommon for folks to lose their door keys and be concerned about security. When you know how to change the locks you will be more at ease.
If you are not the original tenant or owner you will not know the number of extra keys existing. If you call a locksmith to do the job or bring the lock in to them it can be costly. It can cost even more if the locks on your home are not keyed the same or you have a couple of locks on the doors.
With one of these DIY kits you can do the job like the pros at a fraction of what you would pay a locksmith. Kits are available for the common brands of locks. However, the kits are not interchangeable so you might need to get a kit for the different brands that are in your home. With luck all your locks with be the same.
One kit can change as many as 6 locks. If you have more locks to change you can order more pins. The kits can be used for entrance and deadbolt locks and have two keys included. You will also find the tools needed but will have to provide a tweezers and screwdriver. It is important hold on to the original keys to use when you remove the lock cylinder.
Make sure you use the correct kit and check the instructions since there are variations between brands. Your first step is to remove the door knob by inserting the wire that comes with the kit into the hole in the knob and depressing the clip. This will allow you to pull the knob off. Then insert the key in the lock turning it until it is unlocked. Next remove the knob and lock cylinder.
The retainer ring can be removed now. Use the retainer ring tool in your kit and push it against the ring. Pop off the ring. Use the same tool to remove the ring from the cylinder. Keep this ring to replace later. You are now able to take the retainer ring off.
Now you can take the cylinder plug off. Insert the original key and turn left or right. You can now take the plug out using the plug follower in your kit. Insert the follower and push it through cylinder so you can take out the plug. Make sure you apply constant pressure between the plug and follower to avoid losing the pins and springs.
Take the pins out and insert your new key. Use the tweezers to place the new pins in the cylinder. Follow the color guide in your kit. When you finish inserting the pins you will reassemble the lock by following the steps you just took in the reverse. Make certain you have the tools you need before beginning.
If you are not the original tenant or owner you will not know the number of extra keys existing. If you call a locksmith to do the job or bring the lock in to them it can be costly. It can cost even more if the locks on your home are not keyed the same or you have a couple of locks on the doors.
With one of these DIY kits you can do the job like the pros at a fraction of what you would pay a locksmith. Kits are available for the common brands of locks. However, the kits are not interchangeable so you might need to get a kit for the different brands that are in your home. With luck all your locks with be the same.
One kit can change as many as 6 locks. If you have more locks to change you can order more pins. The kits can be used for entrance and deadbolt locks and have two keys included. You will also find the tools needed but will have to provide a tweezers and screwdriver. It is important hold on to the original keys to use when you remove the lock cylinder.
Make sure you use the correct kit and check the instructions since there are variations between brands. Your first step is to remove the door knob by inserting the wire that comes with the kit into the hole in the knob and depressing the clip. This will allow you to pull the knob off. Then insert the key in the lock turning it until it is unlocked. Next remove the knob and lock cylinder.
The retainer ring can be removed now. Use the retainer ring tool in your kit and push it against the ring. Pop off the ring. Use the same tool to remove the ring from the cylinder. Keep this ring to replace later. You are now able to take the retainer ring off.
Now you can take the cylinder plug off. Insert the original key and turn left or right. You can now take the plug out using the plug follower in your kit. Insert the follower and push it through cylinder so you can take out the plug. Make sure you apply constant pressure between the plug and follower to avoid losing the pins and springs.
Take the pins out and insert your new key. Use the tweezers to place the new pins in the cylinder. Follow the color guide in your kit. When you finish inserting the pins you will reassemble the lock by following the steps you just took in the reverse. Make certain you have the tools you need before beginning.
About the Author:
Find details about the advantages of using house rekey services and more info about a reliable locksmith at http://www.salinaslocksmith.com/residential right now.
No comments:
Post a Comment